Outdoor PreAmp TV Antenna Signal Amplifier NEXTGEN, ATSC 3.0, 4K, UHD, HD, HDR For Sale

OUTDOOR TV ANTENNA PRE-AMPLIFIER SIGNAL BOOSTER

Enhance your entertainment experience with the ONN Outdoor Antenna Pre-Amplifier model ONA17CH003 V.2 (Updated Version 2, manufactured by Philips for ONN, same as Philips model SDV9320N/27). Engineered to strengthen broadcast signals for channels in your area, this amplifier is full 1080p and 4K Ultra HD compatible. Its low-noise amplification improves signal-to-noise ratio and compensates for signal loss to provide superior picture and sound.

Mounting hardware and step-by-step instructions make installation a breeze. The durable, weather-resistant design allows you to place it in the best inside or outside location to minimize signal dropouts caused by interference from building materials and walls. This amplifier features input and output coax connections for use with all TV and antenna brands. Gain a new perspective with the Onn Outdoor Antenna Pre-Amplifier.

1. High Gain (18 dB VHF / 16 dB UHF)An 18/16 dB boost is the \"sweet spot\" for outdoor pre-amps. It is strong enough to push a clean signal down a long coaxial cable run (over 100 feet) or through a 2-way to 4-way \"POWER-PASS Splitter\" network without losing picture quality.2. Balanced AmplificationCheaper generic preamps often boost everything blindly, which can overdrive your TV tuner and cause a \"No Signal\" error. By applying slightly more gain to VHF (18 dB) and a bit less to UHF (16 dB), this unit accounts for the fact that VHF signals struggle more with building penetration and interference.3. Low Noise FloorBecause this is installed next to the antenna at the mast (before the signal travels down the long coax cable), it amplifies a clean signal. Boosting a signal by 16–18 dB at the mast is significantly better than using a 30 dB amplifier inside the house, which would just amplify the cable interference hiss and noise.Specifications:

• BOOSTS SIGNAL– Will enhance and strengthen the signal received by your outdoor passive TV antenna. The amplifier will clear up anylow-strength, fuzzy, or pixelated channels.

• NEXTGEN TV (ATSC 3.0) Compatible!

• 4G/5G LTE Filter

• LOW-NOISE AMPLIFICATION– Improves VHF and UHF reception and boosts signal for digital TV signals.

• EASY INSTALLATION–You must perform a new channel scan via TV Menu after installation!

• Intended forOutdoor Use- Can be used indoors too, just make sure the amplifier is installed as close to the outdoor roof mount antenna as possible (3 to 5ft or 10ft if using Quad-shield cable) so the amplifier can boost a clean signal instead of a pixelated signal!

• Made in Taiwan - Not a cheap China product!

• NOTE– Using an amplifier does not mean necessarily that you will receive more TV channels, but it will strengthen the signal of available channels in your area if installed at the distances specified.

• Signal booster – This low-noise Pre-amplifier boosts signal strength to compensate for signal loss, improve picture clarity and minimize reception dropouts when installed 2 to 5ft from the outdoor roof mount antenna (Distance from antenna can be up to 10ft when using RG6 Quad-Shield cable).

• Universal compatibility – Engineered for the future of television, this amplifier is full 1080p, 4k Ultra HD and NextGEN (ATSC 3.0) compatible to deliver high-quality picture and sound and works with all TV and antenna brands.

• Durability - The weather-resistant design allows placement in the best location closest to the outdoor antenna to minimize interference and get optimal signal strength.

• Easy installation - Mounting hardware and step-by-step instructions are included for simple installation.

• See 5th photo: Install the amplifier as close to the outdoor antenna as possible (preferably only a few feet away) and preferably use the highest quality RG6 coaxial cable available throughout the installation from the antenna to the TVs for best results (minimum 100% AL Foil with 60% AL braided coaxial cable or Quad-Shield is highly recommended).The quality of the coaxial cable is as important as the signal amplifier/booster in achieving the best and widest possible TV reception.

• ONLY use \"Power-pass\" splitters between the Power Inserter and the Amplifier otherwise it will make the signal worse than before and could block the voltage feed to the amplifier and damage the Power Inserter!

• DO NOT disconnect or cut the coaxial cable going from the Power Inserter to the Amplifier while the Power Inserter is connected to AC power as this will short out and damage the Amplifier and/or Power Inserter!